Qlogic QLA2100F Spezifikationen Seite 166
- Seite / 243
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
v CHS Mapping: [SCSI Plug and Play Mapping]
v Spinup Delay (Secs): [2]
v Secondary Cluster Server: [No]
v Termination Control: [Auto]
v Restore Defaults: (restores defaults)
f. Set the parameters on the Device Properties panel as follows:
v MT or Sec: [20]
v Data Width: [16]
v Scan ID: [Yes]
v Scan LUNs >0: [Yes]
v Disconnect: [On]
v SCSI Time-out: 240
v Queue Tags: [On]
v Boot Choice: [No]
v Format: [Format]
v Verify: [Verify]
v Restore defaults: (restores defaults)
g. Save the changes and select Symbios Configuration Utility again to verify
that you saved the changes.
7. Restart the server.
8. Load the Symbios driver, and restart the system if instructed to do so.
Installing and configuring the QLogic adapter card
Perform the following steps to install and configure the QLogic QLA1041 adapter
card.
Note: The parameter settings shown are an example. The settings for your
environment might be different.
1. Install the QLogic QLA1041 adapter card in the server.
2. Connect the cable to the ESS port.
3. Start the server.
4. Press Alt+Q to get to the FAST!Util menu.
a. From the Configuration Settings menu, select Host Adapter Settings. Set
the following parameters:
v Host Adapter: Enabled
v Host Adapter BIOS: Disabled
v Host Adapter SCSI ID: 7
v PCI Bus direct memory access (DMA) Burst: Enabled
v Compact disc Boot: Disabled
v SCSI Bus Reset: Enabled
v SCSI Bus Reset Delay: 5
v Concurrent Command or Data: Enabled
v Drivers Load RISC Code: Enabled
v Adapter Configuration: Auto
b. Set the parameters in the SCSI Device Settings menu as follows:
v Disconnects OK: Yes
140 ESS Host Systems Attachment Guide
- Host Systems Attachment Guide 1
- Sixth Edition (November 2001) 4
- Contents 5
- Contents v 7
- Contents vii 9
- Product recycling 15
- Disposing of products 15
- About this guide 17
- Prerequisites 18
- Publications 18
- Ordering ESS publications 19
- The IBM publications center 19
- Other IBM publications 20
- About this guide xix 21
- Other non-IBM publications 23
- Web sites 24
- How to send your comments 24
- About this guide xxiii 25
- Chapter 1. Introduction 27
- Front view 28
- Rear view 28
- Chapter 1. Introduction 5 31
- SCSI adapters 33
- Cable interconnections 33
- VS08043N 34
- Cable lengths 35
- Connecting the SCSI cables 35
- Checking the attachment 36
- Solving attachment problems 36
- LUN affinity 37
- Targets and LUNs 37
- SCSI host system limitations 37
- Fibre-channel architecture 39
- Arbitrated loop 40
- LUN access modes 42
- Access profiles 43
- The anonymous host 43
- Device special files 46
- Initializing disk device 46
- Configuring AdvFS 46
- Adding and assigning volumes 49
- Configuring the storage 52
- Supported switches 55
- Displaying the ESS volume 58
- # mkdir /fs 63
- 9337 subsystem emulation 72
- Recommended configurations 76
- Host Limitations 76
- NUMA-Q host 81
- System requirements 82
- Installing the package 84
- Verifying the configuration 89
- HACMP/6000 90
- Hardware requirements 90
- Attachment procedures 91
- Saving data on the ESS 92
- Restoring data on the ESS 92
- Attaching with ESCON 95
- Cable lengths and path types 97
- Data transfer 97
- Native ESCON configuration 98
- S/390 or 100
- Mixed configuration 102
- Native FICON configuration 103
- Attaching to a FICON channel 104
- Attachment considerations 105
- Attachment requirements 109
- Partitioning ESS disks 113
- Attaching with SCSI adapters 117
- Mapping hardware 126
- /cdrom/unnamed_cdrom 129
- PATH=$PATH:/opt/IBMdpo/bin 129
- JNI adapters 144
- Emulex or QLogic adapters 145
- Boot Order [0] 149
- Next Boot [Off] 149
- Link speed Auto 176
- Performing a basic FlashCopy 177
- Software requirements 185
- Nonconcurrent migration 186
- Administrator window 191
- Concurrent migration 192
- System component LUN limit 195
- Host bus adapter 256 196
- SAN Data Gateway 255 196
- Statement of Limited Warranty 197
- Items Not Covered by Warranty 198
- Warranty Service 198
- Production Status 199
- Limitation of Liability 199
- ASIA PACIFIC 200
- Trademarks 206
- Electronic emission notices 206
- Germany only 207
- Nach der EN 55022: 208
- Anmerkung: 208
- Actions you must not take 209
- Glossary 211
- Glossary 187 213
- Glossary 189 215
- Glossary 191 217
- Glossary 193 219
- Glossary 195 221
- Glossary 197 223
- Glossary 199 225
- Glossary 201 227
- Numerics 228
- Index 205 231
- Index 207 233
- Index 209 235
- Index 211 237
- BUSINESS REPLY MAIL 240
- SC26-7296-05 242
- ESSHostSystemsAttachmentGuide 243
Verwandte Produkte und Handbücher für Software Qlogic QLA2100F
Software Qlogic OFED+ Host Spezifikationen
(20 Seiten)
(20 Seiten)
Software Qlogic QLA2102F Spezifikationen
(114 Seiten)
(114 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern